MODIFIEDLIFE

2011 Jeep Liberty Car Alarm Wire Chart

2011 Jeep Liberty Alarm Wires

Find the right alarm wire colors, locations, and polarity with this 2011 Jeep Liberty alarm wiring diagram. This will help you install your car alarm wiring correctly.

Application Wire Color and Location
Battery Constant 12v+ Positive Wire (+) Blue/Red (This wire only supplies 10 amps of current, for high current application go directly to the battery.)
Battery Constant 12v+ Positive Wire Location Ignition Switch Harness
Starter Positive Wire (+) Yellow/Gray (Not for Remote Start)
Starter Positive Wire Location Ignition Switch Harness
Second Starter Positive Wire (+) Violet/Brown (This wire is also the key sense and accessory wire, use a 180 ohm resistor for second start for remote start.)
Second Starter Positive Wire Location Ignition Switch Harness
Ignition Positive Wire (+) Pink/White
Ignition Positive Wire Location Ignition Switch Harness
Second Ignition Positive Wire (+) N/A
Second Ignition Positive Wire Location N/A
Third Ignition Positive Wire (+) N/A
Third Ignition Positive Wire Location N/A
Accessory Positive Wire (+) Violet/Brown (This wire is also the key sense and second starter wire, use a 580 ohm resistor for second accessory for remote start.)
Accessory Positive Wire Location Ignition Switch Harness
Second Accessory Positive Wire (+) N/A
Second Accessory Positive Wire Location N/A
Key Sense Wire Violet/Brown
Key Sense Wire Location Ignition Switch Harness

2011 Jeep Liberty Alarm Sensor Wires

Find the right alarm sensor wire colors, locations, and polarity with this 2011 Jeep Liberty alarm sensor wire chart. This will help you connect all your car alarm sensors correctly.

Application Wire Color and Location
Parking Light Negative Wire (-) N/A
Parking Light Negative Wire Location N/A
Parking Light Positive Wire (+) White/Violet
Parking Light Positive Wire Location At Harness in Driver Kick Panel
Power Door Lock Negative Wire (-) Violet/Dark Green (Lock is (-) through a 330 ohm resistor. Must use relay.)
Power Door Lock Negative Wire Location In Harness in Driver Kick Panel
Power Door Unlock Negative Wire (-) Violet/Dark Green (Unlock is (-) through a 100 ohm resistor. Must use relay.)
Power Door Unlock Negative Wire Location In Harness in Driver Kick Panel
Door Trigger Negative Wire (-) Use all door triggers and diode isolate each wire.
Door Trigger Negative Wire Location At each door
Dome Light Supervision Wire (-) Yellow/White
Dome Light Supervision Wire Location In Harness in Driver Kick Panel
Trunk Trigger Negative Wire (-) Violet/Orange
Trunk Trigger Negative Wire Location In Harness in Driver Kick Panel
Trunk Release Negative Wire (-) N/A
Trunk Release Negative Wire Location N/A
Sliding Power Door Wire N/A
Sliding Power Door Wire Location N/A
Horn Negative Wire (-) Dark Green/Violet
Horn Negative Wire Location In Harness at Steering Column
Tachometer Wire Negative Wire (-) N/A
Tachometer Wire Negative Wire Location N/A
Wait To Start Wire N/A
Wait To Start Location N/A
Brake Light Positive Wire (+) White/Tan
Brake Light Positive Wire Location At Switch Above the Brake Pedal
Factory Alarm Arm Wire (-) N/A
Factory Alarm Arm Wire Location N/A
Factory Alarm Disarm Wire (-) N/A
Factory Alarm Disarm Wire Location N/A
Factory Anti-Theft System Daimler Sentry Key Vehicle Immobilizer
Factory Anti-Theft System Location Key Sends RF Signal to the BCM Module

Feel free to use any 2011 Jeep Liberty alarm wiring diagram that is listed here but keep in mind that all information here is provided as is without any warranty of any kind. Use of this 2011 Jeep Liberty car alarm wire chart is at your own risk. Always verify all wires, wire colors and connection points before applying any information found here to your 2011 Jeep Liberty.

Leave a Comment

Your email address will not be published. Required fields are marked *