2007 Toyota Sequoia Alarm Wires
Find the right alarm wire colors, locations, and polarity with this 2007 Toyota Sequoia alarm wiring diagram. This will help you install your car alarm wiring correctly.
Application | Wire Color and Location |
---|---|
Battery Constant 12v+ Positive Wire (+) | White/Blue |
Battery Constant 12v+ Positive Wire Location | Ignition Switch Harness |
Starter Positive Wire (+) | Black/White |
Starter Positive Wire Location | Ignition Switch Harness |
Second Starter Positive Wire (+) | N/A |
Second Starter Positive Wire Location | N/A |
Ignition Positive Wire (+) | Black/Red |
Ignition Positive Wire Location | Ignition Switch Harness |
Second Ignition Positive Wire (+) | Black/Yellow |
Second Ignition Positive Wire Location | Ignition Switch Harness |
Third Ignition Positive Wire (+) | N/A |
Third Ignition Positive Wire Location | N/A |
Accessory Positive Wire (+) | Pink |
Accessory Positive Wire Location | Ignition Switch Harness |
Second Accessory Positive Wire (+) | N/A |
Second Accessory Positive Wire Location | N/A |
Key Sense Wire (-) | Yellow/Green |
Key Sense Wire Location | At BECU, White Plug, Pin 13. The BECU (body electronic control unit) is located above the drivers kick panel. |
2007 Toyota Sequoia Alarm Sensor Wires
Find the right alarm sensor wire colors, locations, and polarity with this 2007 Toyota Sequoia alarm sensor wire chart. This will help you connect all your car alarm sensors correctly.
Application | Wire Color and Location |
---|---|
Parking Light Negative Wire (-) | Green |
Parking Light Negative Wire Location | At BECU, Gray Plug, Pin 7. The BECU (body electronic control unit) is located above the drivers kick panel. |
Parking Light Positive Wire (+) | Green |
Parking Light Positive Wire Location | In Drivers Kick Panel, Harness To Rear Of Vehicle |
Power Door Lock Negative Wire (-) | This vehicle will require an extra relay and diodes to do the keyless entry function. |
Power Door Lock Negative Wire Location | N/A |
Power Door Unlock Negative Wire (-) | This vehicle will require an extra relay and diodes to do the keyless entry function. |
Power Door Unlock Negative Wire Location | N/A |
Door Trigger Negative Wire (-) | The driver door is a gray/red (-) in the black plug, pin 12. The passenger door is a light green/black (-) in the white plug, pin 22. The drivers rear door is a red/white (-) in the black plug, pin 7. The passenger rear door is a red/white (-) in the white plug, pin 8. When connecting to an alarm system, use all (4) door trigger wires and diode isolate. |
Door Trigger Negative Wire Location | At BECU. The BECU (body electronic control unit) is located above the drivers kick panel. |
Dome Light Supervision Wire (-) | White |
Dome Light Supervision Wire Location | At BECU, Black Plug, Pin 3. The BECU (body electronic control unit) is located above the drivers kick panel. |
Trunk Release Negative Wire (-) | N/A |
Trunk Release Negative Wire Location | N/A |
Sliding Power Door Wire | N/A |
Sliding Power Door Wire Location | N/A |
Horn Negative Wire (-) | Brown/Yellow |
Horn Negative Wire Location | At BECU, White Plug, Pin 26. The BECU (body electronic control unit) is located above the drivers kick panel. |
Tachometer Wire Negative Wire (-) | Yellow/Green |
Tachometer Wire Negative Wire Location | At ECM, 2nd Plug From Right, Pin 1. The ECM (engine control module) is located behind the glove box. |
Wait To Start Wire | N/A |
Wait To Start Location | N/A |
Brake Light Positive Wire (+) | Green/Yellow |
Brake Light Positive Wire Location | At Switch Above Brake Pedal |
Factory Alarm Disarm Wire (-) | Disarms With Keysense Wire. The key sense wire will disarm the vehicle without unlocking the doors by applying a (-) negative to this wire during remote starting. |
Factory Alarm Disarm Wire Location | At Ignition Switch Harness |
Factory Anti-Theft System | Transponder Anti-Theft System, Requires Bypass Module And Extra Ignition Key |
Factory Anti-Theft System Location | Transponder At Ignition Switch Tumbler |
Feel free to use any 2007 Toyota Sequoia alarm wiring diagram that is listed here but keep in mind that all information here is provided as is without any warranty of any kind. Use of this 2007 Toyota Sequoia car alarm wire chart is at your own risk. Always verify all wires, wire colors and connection points before applying any information found here to your 2007 Toyota Sequoia.
2 thoughts on “2007 Toyota Sequoia Car Alarm Wiring Diagram”
Jeff, it sounds like your 2007 Toyota Sequoia alarm shock sensor is too sensitive. You need to lower the shocks sensor sensitivity to prevent you alarm from going off when cars drive by. Some alarm systems have external shock sensors which can be adjusted externally. Some alarm systems have built in shock sensors which can only be adjusted via alarm programming. If you have never adjusted or programmed your alarm system before, our advice is that you take your car to an experienced alarm installer. It should not take more than 30 minutes from start to finish to adjust it. Hope this helps. Good luck with your 2007 Toyota Sequoia shock sensor adjustment.
Why does the 2007 Toyota Sequoia alarm keep going off suddenly even without triggering or tampering the car? Battery still good. Thanks