2003 Chrysler Voyager Auto Alarm Wiring Instructions


Whether your an expert Chrysler Voyager car alarm installer, Chrysler Voyager performance fan or a novice Chrysler Voyager enthusiast with a 2003 Chrysler Voyager, a Chrysler Voyager car alarm wiring diagram can save yourself a lot of time. One of the most time consuming tasks with installing an after market car alarm, car security, car remote start, automatic remote starter, shock sensor, tilt sensor, car alarm sensor or any auto alarm is identifying the correct color car security wires for a 2003 Chrysler Voyager headlight bulb size you need for your low beam or high beam and save time. Also, find your other car light bulb sizes including your fog light, reverse light, turn signal, brake light and more. It’s that easy!

The Modified Life staff has taken all its Chrysler Voyager car alarm wiring diagrams, Chrysler Voyager car security wiring diagrams, Chrysler Voyager car alarm wire diagrams, Chrysler Voyager car security wiring schematics, Chrysler Voyager car security diagrams, Chrysler Voyager remote starter wiring diagrams and cataloged them online for our visitors to use for free. Our automotive wiring diagrams allow you to enjoy your new auto security electronics rather than spend countless hours trying to figure out which wires goes where.

Feel free to use any Chrysler Voyager auto alarm wiring diagram that is listed on Modified Life but keep in mind that all information here is provided as-is without any warranty of any kind and most of the auto security wiring diagrams listed on our enthusiast website are submitted by the Modified Life community. Use of the wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your 2003 Chrysler Voyager.

Questions

If you have any questions pertaining to the car wiring in a 2003 Chrysler Voyager, please feel free to post it at the bottom of this page and either we will do our best to find you the information you need or hopefully someone in the Modified Life community will have the information you are looking for.

Request a Car Alarm Wiring Diagram

If you can not find your car alarm wiring, car security wire diagram or auto alarm wire diagram on Modified Life, please feel free to post a car alarm wiring diagram request on this page and we will do our best to find you the diagram, schematic or information you need for your mobile security installation.

Adding More Information

If you would like to help the Modified Life community by adding a car security wire schematic, car alarm wire diagram, car remote starter wire diagram, auto remote starter wire diagram or auto security wire diagram to our resource, please feel free to post any additional car wiring information about the 2003 Chrysler Voyager on this page.

2003 Chrysler Voyager Auto Alarm Wiring Instructions

Battery Constant 12v+ Positive Wire (+): Connect To Battery Only
Battery Constant 12v+ Positive Wire Location: N/A

Starter Positive Wire (+): Yellow
Starter Positive Wire Location: Ignition Switch Harness

Second Starter Positive Wire (+): Purple/Brown (To remote start this vehicle and turn on the ac/heater will require an extra relay and a negative through a 180 ohm resistor, this must be installed to operate in remote start mode.)
Second Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Pink/White
Ignition Positive Wire Location: Ignition Switch Harness

Second Ignition Positive Wire (+): N/A
Second Ignition Positive Wire Location: Ignition Switch Harness

Third Ignition Positive Wire (+): N/A
Third Ignition Positive Wire Location: N/A

Accessory Positive Wire (+): N/A
Accessory Positive Wire Location: N/A

Second Accessory Positive Wire (+): N/A
Second Accessory Positive Wire Location: N/A

Key Sense Wire: N/A
Key Sense Wire Location: N/A

Parking Light Negative Wire (-): White/Brown (To turn on the parking lights requires a negative through a 2000 ohm resistor and an extra relay.)
Parking Light Negative Wire Location: At Headlight Switch

Parking Light Positive Wire (+): Do Not Use
Parking Light Positive Wire Location: N/A

Power Door Lock Negative Wire (-): Purple/Green (1-Wire Door Lock System). This vehicle uses a 1-wire door locking system requiring a negative through a 5200 ohm for lock, and a negative through a 2000 ohm resistor for unlock, some units will also require 2 extra relays.
Power Door Lock Negative Wire Location: At BCM Module, Connector 3, Pin 21

Power Door Unlock Negative Wire (-): Same Wire As Above
Power Door Unlock Negative Wire Location: N/A

Door Trigger Negative Wire (-): This vehicle uses 4 door pin trigger wires, the drivers door is a purple (-) at pin 6, the passengers door is a purple/white (-) pin 7, the drivers side sliding door is a purple/grey, pin 8 and the passenger side sliding door is a purple/yellow, pin 5. When connecting to an alarm system use all 4 wires and diode isolate.
Door Trigger Negative Wire Location: At BCM Module, Connector 3. The BCM Module (body control module is located in the drivers kick panel, near the parking brake. The BCM Module has 5 plugs, (1) 6-pin plug, and (4) 34-pin plugs.

Dome Light Supervision Wire (-): Purple
Dome Light Supervision Wire Location: At BCM Module, Connector 3, Pin 6. The BCM Module (body control module is located in the drivers kick panel, near the parking brake. The BCM Module has 5 plugs, (1) 6-pin plug, and (4) 34-pin plugs.

Trunk Release Negative Wire (-): Purple/Tan (The sliding doors require a negative through a 1500 ohm resistor for the drivers door and a negative through a 2700 ohm resistor for the passenger door. Units will also require an extra relay for each door.)
Trunk Release Negative Wire Location: At BCM Module, Connector 2, Pin 6. The BCM Module (body control module is located in the drivers kick panel, near the parking brake. The BCM Module has 5 plugs, (1) 6-pin plug, and (4) 34-pin plugs.

Sliding Power Door Wire (-): Purple/Blue (The tach wire on the 2.4 liter is blue/green or blue/tan. On the 3.3 liter and 3.8 liter, use the blue/green, blue/tan or blue/orange.)
Sliding Power Door Wire Location: At BCM Module, Connector 3, Pin 1. The BCM Module (body control module is located in the drivers kick panel, near the parking brake. The BCM Module has 5 plugs, (1) 6-pin plug, and (4) 34-pin plugs.

Horn Negative Wire (-): Black/Red
Horn Negative Wire Location: At Steering Column Harness

Tachometer Wire Negative Wire (-): Gray Or Gray/Red
Tachometer Wire Negative Wire Location: At Ignition Coil Pack

Wait To Start Wire: N/A
Wait To Start Location: N/A

Brake Light Positive Wire (+): White/Tan
Brake Light Positive Wire Location: At Switch Above Brake Pedal

Factory Alarm Disarm Wire (-): Purple/Light Blue (This vehicle will disarm with a negative through a 9000 ohm resistor, must use single pulse to disarm and a double pulse on this wire will also unlock.)
Factory Alarm Disarm Wire Location: At BCM Module, Connector 3, Pin 14. The BCM Module (body control module is located in the drivers kick panel, near the parking brake. The BCM Module has 5 plugs, (1) 6-pin plug, and (4) 34-pin plugs.

Factory Anti-Theft System: Chrysler Sentry Key (Gray Key Only) A Transponder System
Factory Anti-Theft System Location: Transponder At Ignition Switch Tumbler

The 2003 Chrysler Voyager alarm wire color and location information above is updated as it is submitted by the Modified Life community.

Leave a Reply

Your email address will not be published.

9 + six =