2001 Mitsubishi Mirage Car Radio Wiring Diagram

  1. All Car Makes
  2. »
  3. Mitsubishi Radio Stereo Wiring Diagrams
  4. »
  5. 2001 Mitsubishi Mirage Car Radio Wiring Diagram


Whether your an expert Mitsubishi Mirage mobile electronics installer, Mitsubishi Mirage fanatic, or a novice Mitsubishi Mirage enthusiast with a 2001 Mitsubishi Mirage, a car stereo wiring diagram can save yourself a lot of time. Automotive wiring in a 2001 Mitsubishi Mirage vehicles are becoming increasing more difficult to identify due to the installation of more advanced factory oem electronics.

One of the most time consuming tasks with installing an after market car stereo, car radio, satellite radio, xm radio, car speakers, tweeters, car subwoofer, crossovers, audio equalizer, car amplifier, mobile amp, car amplifier, mp3 player, ipod or any car audio electronics is identifying the correct color car audio wires for your 2001 Mitsubishi Mirage headlight bulb size you need for your low beam or high beam and save time. Also, find your other car light bulb sizes including your fog light, reverse light, turn signal, brake light and more. It’s that easy!

The Modified Life staff has taken all its Mitsubishi Mirage car radio wiring diagrams, Mitsubishi Mirage car audio wiring diagrams, Mitsubishi Mirage car stereo wiring diagrams, Mitsubishi Mirage car radio wiring schematics, Mitsubishi Mirage car wiring diagrams and cataloged them online for use by our visitors for free. Our automotive wiring diagrams allow you to enjoy your new mobile electronics rather than spend countless hours trying to figure out which wires goes to which 2001 Mitsubishi Mirage part or component.

Feel free to use any Mitsubishi Mirage car stereo wiring diagram that is listed on Modified Life but keep in mind that all information here is provided “as is” without any warranty of any kind and most of the car audio wiring diagrams listed on our enthusiast website are submitted by the Modified Life community. Use of the Mitsubishi Mirage wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your 2001 Mitsubishi Mirage.

Questions

If you have any questions pertaining to the audio system in the 2001 Mitsubishi Mirage, please feel free to post it at the bottom of this page and either we’ll do our best to find you the information you need or hopefully someone in the Modified Life community will have the information you’re looking for.

Request a Car Stereo Wiring Diagram

If you can’t find a particular car audio wire diagram on Modified Life, please feel free to post a car radio wiring diagram request at the bottom of this page and we’ll do our best to find you the diagram or schematic you need for your mobile audio installation.

Adding More Information

If you would like to help the Modified Life community by adding any missing information or adding a new car audio wire diagram to our resource, please feel free to post it at the bottom of this page.

2001 Mitsubishi Mirage Car Radio Wiring Diagram

Car Radio Battery Constant 12v+ Wire: Red/Black
Car Radio Accessory Switched 12v+ Wire: Blue
Car Radio Ground Wire: Chassis
Car Radio Illumination Wire: Green/White
Car Stereo Dimmer Wire: Black/Yellow
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Red/White
Left Front Speaker Negative Wire (-): Red/Blue
Right Front Speaker Positive Wire (+): Red
Right Front Speaker Negative Wire (-): Blue
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Yellow/Brown
Left Rear Speaker Negative Wire (-): Yellow/Red
Right Rear Speaker Positive Wire (+): Light Green
Right Rear Speaker Negative Wire (-): Yellow/Green

8 thoughts on “2001 Mitsubishi Mirage Car Radio Wiring Diagram”

  1. This is the wiring on my car:

    Right Rear + = Aqua
    Right Rear – = Yellow with Green stripe
    Right Front + = Red
    Right Front – = Skinny Blue
    Left Rear + = Yellow with BLUE stripe (not brown)
    Left Rear – = Yellow with Red stripe
    Left Front + = Red with White stripe
    Left Front – = Red with Blue stripe
    Ignition switch (ACC) 12V = Thick Blue
    Constant 12V = Red w/ Black stripe
    Antenna Power – Whatever is left (I think Green w/ Brown stripe)

    What was weird for me is that my aftermarket device had a thick wire for the constant 12V and the mirage had a skinny one, while it was the same opposite situation with the ignition switch, but putting those together how I have outlined above is correct. I also don’t have a power antenna where it will raise out of the car but I had to make sure and connect the Antenna Power wire to my new Antenna Power wire and everything started working.

    Reply
  2. i just bought a JVC KD-S37 CD Receiver and i have a problem finding the memory connection to my 1999 Mitsubishi Mirage

    Reply
  3. Cesar, most vehicles have a factory hole with a rubber or plastic grommet at the firewall. This is usually the standard place to run a power wire through the firewall. If one of these holes are not available or not large enough, a hole will have to be drilled to accommodate your power wire. Choose something on the engine side of the firewall as reference and try to match it up on the interior side of the firewall. This will make sure you do not drill through anything important. Then drill a hole somewhere near or beside your reference point. Hope this helps. Good luck with your amplifier installation.

    Reply
  4. I’m trying to install a amplifier into my car… exept i cant find a spot in the firewall to run a cable to the battery any help on where to put it, or where to put a hole in the firewall?

    Reply
  5. Nelson, you have to ground your aftermarket radio to the chassis (vehicle frame) when you don’t have a factory ground wire in the stereo wire harness. Simply ground your wire to the chassis (look below).

    1. Find some bare metal on your vehicle (somewhere near your factory radio harness). Make sure this bare metal touches the chassis (frame) of the vehicle.

    Bare Metal for Chassis Grounding

    2. Connect a ring terminal to the black wire coming off your aftermarket radio harness.

    Ground Wire with Ring Terminal

    3. Use a self tapping screw to attach the black wire with ring terminal to the bare metal.

    Self Tapping Screw

    Hope this helps. Good luck with grounding your car stereo.

    Reply
  6. I am trying to install the 2001 Mitsubishi Mirage radio into another car, but the thing is I need to ground the radio and since there is no ground wire on this radio how do you ground it to the chasis?

    Reply

Leave a Comment

4 + three =