1999 Mercury Villager Car Alarm Wiring Guide


Whether your an expert Mercury Villager car alarm installer, Mercury Villager performance fan or a novice Mercury Villager enthusiast with a 1999 Mercury Villager, a Mercury Villager car alarm wiring diagram can save yourself a lot of time. One of the most time consuming tasks with installing an after market car alarm, car security, car remote start, automatic remote starter, shock sensor, tilt sensor, car alarm sensor or any auto alarm is identifying the correct color car security wires for a 1999 Mercury Villager headlight bulb size you need for your low beam or high beam and save time. Also, find your other car light bulb sizes including your fog light, reverse light, turn signal, brake light and more. It’s that easy!

The Modified Life staff has taken all its Mercury Villager car alarm wiring diagrams, Mercury Villager car security wiring diagrams, Mercury Villager car alarm wire diagrams, Mercury Villager car security wiring schematics, Mercury Villager car security diagrams, Mercury Villager remote starter wiring diagrams and cataloged them online for our visitors to use for free. Our automotive wiring diagrams allow you to enjoy your new auto security electronics rather than spend countless hours trying to figure out which wires goes where.

Feel free to use any Mercury Villager auto alarm wiring diagram that is listed on Modified Life but keep in mind that all information here is provided “as is” without any warranty of any kind and most of the auto security wiring diagrams listed on our enthusiast website are submitted by the Modified Life community. Use of the wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your 1999 Mercury Villager.

Questions

If you have any questions pertaining to the car wiring in a 1999 Mercury Villager, please feel free to post it at the bottom of this page and either we’ll do our best to find you the information you need or hopefully someone in the Modified Life community will have the information you are looking for.

Request a Car Alarm Wiring Diagram

If you can’t find your car alarm wiring, car security wire diagram or auto alarm wire diagram on Modified Life, please feel free to post a car alarm wiring diagram request on this page and we’ll do our best to find you the diagram, schematic or information you need for your mobile security installation.

Adding More Information

If you would like to help the Modified Life community by adding a car security wire schematic, car alarm wire diagram, car remote starter wire diagram, auto remote starter wire diagram or auto security wire diagram to our resource, please feel free to post any additional car wiring information about the 1999 Mercury Villager on this page.

1999 Mercury Villager Car Alarm Wiring Guide

Battery Constant 12v+ Positive Wire (+): White/Red
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Black/Yellow
Starter Positive Wire Location: Ignition Switch Harness

Second Starter Positive Wire (+): Black/Green
Second Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Black/White
Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Blue
Accessory Positive Wire Location: Ignition Switch Harness

Secondary Accessory Positive Wire (+): Red
Secondary Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Negative Wire (-): Gray/Red
Parking Light Negative Wire Location: At Headlight Switch

Parking Light Positive Wire (+): Do Not Use.
Parking Light Positive Wire Location: N/A

Power Door Lock Negative Wire (-): Red
Power Door Lock Negative Wire Location: In Either Door Harness

Power Door Unlock Negative Wire (-): Red/Black (Requires Double Pulse)
Power Door Unlock Negative Wire Location: In Either Door Harness

Door Trigger Positive Wire (+): In the drivers kick panel use the red (-) for the drivers door and for the rear lift gate use the red/white (-), for the passenger door use the red/white (-) and the red/green (-) for the sliding door these wires are in the passenger kick panel. When connecting to an alarm system, use all 4 door trigger wires and diode isolate.
Door Trigger Positive Wire Location: In Each Kick Panel

Domelight Supervision Wire (-): Brown/White (Requires Relay)
Domelight Supervision Wire Location: Low In Drivers Kick Panel

Horn Negative Negative Wire (-): Light Blue/Black
Horn Negative Negative Wire Location: At Steering Column Harness

Tachometer Wire Negative Wire (-): White
Tachometer Wire Negative Wire Location: At PCM (Pin 2). The PCM (powertrain control module) is located behind the glove box.

Brake Light Positive Wire (+): Yellow/Black
Brake Light Positive Wire Location: At Switch Above Brake Pedal

Factory Alarm Disarm Wire (-): Disarms With Unlock, Single Pulse Disarms
Factory Alarm Disarm Wire Location: N/A

Factory Anti-Theft Wire (-): N/A
Factory Anti-Theft Wire Location: N/A

Leave a Reply

Your email address will not be published. Required fields are marked *

eleven + 3 =