2007 Chevrolet Corvette Alarm Wires
Find the right alarm wire colors, locations, and polarity with this 2007 Chevrolet Corvette alarm wiring diagram. This will help you install your car alarm wiring correctly.
Application | Wire Color and Location |
---|---|
Battery Constant 12v+ Positive Wire (+) | Red/Black |
Battery Constant 12v+ Positive Wire Location | At BCM Module, C3, Pin D1. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors – C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector. |
Starter Positive Wire (+) | Purple (Not Required For Remote Start) |
Starter Positive Wire Location | At Starter Or Fuse Block Under Hood |
Second Starter Positive Wire (+) | N/A |
Second Starter Positive Wire Location | N/A |
Ignition Positive Wire (+) | Pink (Not Required For Remote Start) |
Ignition Positive Wire Location | At BCM Module, C4, Pin C8. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors – C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector. |
Second Ignition Positive Wire (+) | N/A |
Second Ignition Positive Wire Location | N/A |
Third Ignition Positive Wire (+) | N/A |
Third Ignition Positive Wire Location | N/A |
Accessory Positive Wire (+) | N/A |
Accessory Positive Wire Location | N/A |
Second Accessory Positive Wire (+) | N/A |
Second Accessory Positive Wire Location | N/A |
Key Sense Wire | N/A |
Key Sense Wire Location | N/A |
2007 Chevrolet Corvette Alarm Sensor Wires
Find the right alarm sensor wire colors, locations, and polarity with this 2007 Chevrolet Corvette alarm sensor wire chart. This will help you connect all your car alarm sensors correctly.
Application | Wire Color and Location |
---|---|
Parking Light Negative Wire (-) | Brown/White |
Parking Light Negative Wire Location | At BCM Module, Plug C2, Pin 5. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors – C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector. |
Parking Light Positive Wire (+) | Brown |
Parking Light Positive Wire Location | At Harness Going To Rear Of Vehicle |
Power Door Lock Negative Wire (-) | Orange/Black |
Power Door Lock Negative Wire Location | At Lock Switch In Drivers Door |
Power Door Unlock Negative Wire (-) | Orange/Black |
Power Door Unlock Negative Wire Location | At Lock Switch In Drivers Door |
Door Trigger Negative Wire (-) | Gray/Black and Tan/White (Use Both). This vehicle has (2) door pin trigger wires. When connecting to an alarm system, you will need to use both and diode isolate. |
Door Trigger Negative Wire Location | At BCM Module, C1, Pins 51 and 53. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors – C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector. |
Dome Light Supervision Wire (-) | White |
Dome Light Supervision Wire Location | At BCM Module, C3, Pin A10. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors – C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector. |
Trunk Release Negative Wire (-) | Brown/White |
Trunk Release Negative Wire Location | At BCM Module, C1, Pin 71. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors – C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector. |
Sliding Power Door Wire | N/A |
Sliding Power Door Wire Location | N/A |
Horn Negative Wire (-) | Yellow To Tan |
Horn Negative Wire Location | At BCM Module, C2, Pin 14. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors – C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector. |
Tachometer Wire Negative Wire (-) | White |
Tachometer Wire Negative Wire Location | At ECM Module, Blue Plug Pin 48. The ECM module is located in the front passenger fender, remove the wheel to access the panel located behind the wheel. The access panel will let you get to the ECM module. |
Wait To Start Wire | N/A |
Wait To Start Location | N/A |
Brake Light Positive Wire (+) | Light Blue |
Brake Light Positive Wire Location | At BCM Module, C4, Pin D4. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors – C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector. |
Factory Alarm Disarm Wire (-) | Disarms With Factory Remote Only |
Factory Alarm Disarm Wire Location | N/A |
Factory Anti-Theft System | N/A |
Factory Anti-Theft System Location | N/A |
Feel free to use any 2007 Chevrolet Corvette alarm wiring diagram that is listed here but keep in mind that all information here is provided as is without any warranty of any kind. Use of this 2007 Chevrolet Corvette car alarm wire chart is at your own risk. Always verify all wires, wire colors and connection points before applying any information found here to your 2007 Chevrolet Corvette.