2006 Jeep Commander Alarm Wires
Find the right alarm wire colors, locations, and polarity with this 2006 Jeep Commander alarm wiring diagram. This will help you install your car alarm wiring correctly.
Application | Wire Color and Location |
---|---|
Battery Constant 12v+ Positive Wire (+) | Light Blue/Red |
Battery Constant 12v+ Positive Wire Location | At Ignition Harness |
Starter Positive Wire (+) | Pink/Orange |
Starter Positive Wire Location | At Ignition Harness |
Secondary Starter Negative Wire (-) | Purple/Brown (The starter #2 and accessory wire are the same, the starter #2 wire requires a (-) negative through a 180 ohm resistor, and an extra relay, the accessory wire requires a (-) negative through a 560 ohm resistor and an extra relay.) |
Secondary Starter Negative Wire Location | At Ignition Harness |
Ignition Positive Wire (+) | Pink/Light Green |
Ignition Positive Wire Location | At Ignition Harness |
Accessory Positive Wire (+) | The starter #2 and accessory wire are the same, the starter #2 wire requires a (-) negative through a 180 ohm resistor, and an extra relay, the accessory wire requires a (-) negative through a 560 ohm resistor and an extra relay. |
Accessory Positive Wire Location | At Ignition Harness |
2006 Jeep Commander Alarm Sensor Wires
Find the right alarm sensor wire colors, locations, and polarity with this 2006 Jeep Commander alarm sensor wire chart. This will help you connect all your car alarm sensors correctly.
Application | Wire Color and Location |
---|---|
Power Door Lock Negative Wire (-) | Purple/Dark Green (1-Wire Door Locking System). This vehicle is a 1-wire door locking system, the lock requires a (-) negative through a 330 ohm resistor the unlock requires a (-) negative through a 100 ohm resistor. Some units will also require extra relays. |
Power Door Lock Negative Wire Location | At Drivers Door Module In Drivers Door |
Power Door Unlock Negative Wire (-) | Same Wire as Above. |
Power Door Unlock Negative Wire Location | N/A |
Door Trigger Positive Wire (+) | The drivers door is a purple (-) at pin 6, the passenger door is a purple/white (-) pin 7, the drivers rear door is a purple/gray (-) pin 4 and the passenger rear door is a purple/yellow pin 5 when connecting to an alarm system use all 4 wires and diode isolate. |
Door Trigger Positive Wire Location | In Each Kick Panel or Cluster (Connector 3). |
Dome Light Supervision Wire (-) | Yellow/Orange (Requires Relay) |
Dome Light Supervision Wire Location | At Under Dash Light or Cluster (Connector 2, Pin 12). |
Trunk Release Negative Wire (-) | Orange/Purple (Requires Relay). Test this wire while opening the rear glass from the switch on the rear hatch. |
Trunk Release Negative Wire Location | In Drivers Kick Panel or Cluster (Connector 3, Pin 8). |
Horn Negative Positive Wire (+) | Dark Green/Orange |
Horn Negative Positive Wire Location | At Horn or IMP (Connector 2, Pin 35). The IPM (integrated power module) is located on the drivers fender, behind the battery. |
Tachometer Wire Negative Wire (-) | Any Wire Not Red/Tan or Dark Green/Light Green |
Tachometer Wire Negative Wire Location | At Any Ignition Coil or Fuel-Injector |
Brake Light Positive Wire (+) | White/Tan |
Brake Light Positive Wire Location | At Switch Above Brake Pedal |
Factory Alarm Disarm Wire (-) | Disarms With Factory Remote Only. |
Factory Alarm Disarm Wire Location | N/A |
Factory Anti-Theft Wire (-) | Chryslers Sentry Transponder Anti-Theft System |
Factory Anti-Theft Wire Location | At Ignition Tumbler |
Feel free to use any 2006 Jeep Commander alarm wiring diagram that is listed here but keep in mind that all information here is provided as is without any warranty of any kind. Use of this 2006 Jeep Commander car alarm wire chart is at your own risk. Always verify all wires, wire colors and connection points before applying any information found here to your 2006 Jeep Commander.