2006 Chevrolet Corvette Car Alarm Wiring Instructions


Whether your an expert Chevrolet Corvette car alarm installer, Chevrolet Corvette performance fan or a novice Chevrolet Corvette enthusiast with a 2006 Chevrolet Corvette, a Chevrolet Corvette car alarm wiring diagram can save yourself a lot of time. One of the most time consuming tasks with installing an after market car alarm, car security, car remote start, automatic remote starter, shock sensor, tilt sensor, car alarm sensor or any auto alarm is identifying the correct color car security wires for a 2006 Chevrolet Corvette headlight bulb size you need for your low beam or high beam and save time. Also, find your other car light bulb sizes including your fog light, reverse light, turn signal, brake light and more. It’s that easy!

The Modified Life staff has taken all its Chevrolet Corvette car alarm wiring diagrams, Chevrolet Corvette car security wiring diagrams, Chevrolet Corvette car alarm wire diagrams, Chevrolet Corvette car security wiring schematics, Chevrolet Corvette car security diagrams, Chevrolet Corvette remote starter wiring diagrams and cataloged them online for our visitors to use for free. Our automotive wiring diagrams allow you to enjoy your new auto security electronics rather than spend countless hours trying to figure out which wires goes where.

Feel free to use any Chevrolet Corvette auto alarm wiring diagram that is listed on Modified Life but keep in mind that all information here is provided as-is without any warranty of any kind and most of the auto security wiring diagrams listed on our enthusiast website are submitted by the Modified Life community. Use of the wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your 2006 Chevrolet Corvette.

Questions

If you have any questions pertaining to the car wiring in a 2006 Chevrolet Corvette, please feel free to post it at the bottom of this page and either we will do our best to find you the information you need or hopefully someone in the Modified Life community will have the information you are looking for.

Request a Car Alarm Wiring Diagram

If you can not find your car alarm wiring, car security wire diagram or auto alarm wire diagram on Modified Life, please feel free to post a car alarm wiring diagram request on this page and we will do our best to find you the diagram, schematic or information you need for your mobile security installation.

Adding More Information

If you would like to help the Modified Life community by adding a car security wire schematic, car alarm wire diagram, car remote starter wire diagram, auto remote starter wire diagram or auto security wire diagram to our resource, please feel free to post any additional car wiring information about the 2006 Chevrolet Corvette on this page.

2006 Chevrolet Corvette Car Alarm Wiring Instructions

Battery Constant 12v+ Positive Wire (+): Red/Black
Battery Constant 12v+ Positive Wire Location: At BCM Module, C3, Pin D1. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors: C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector.

Starter Positive Wire (+): Purple (Not Required For Remote Start)
Starter Positive Wire Location: At Starter Or Fuse Block Under Hood

Second Starter Positive Wire (+): N/A
Second Starter Positive Wire Location: N/A

Ignition Positive Wire (+): Pink (Not Required For Remote Start)
Ignition Positive Wire Location: At BCM Module, C4, Pin C8. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors: C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector.

Second Ignition Positive Wire (+): N/A
Second Ignition Positive Wire Location: N/A

Third Ignition Positive Wire (+): N/A
Third Ignition Positive Wire Location: N/A

Accessory Positive Wire (+): N/A
Accessory Positive Wire Location: N/A

Second Accessory Positive Wire (+): N/A
Second Accessory Positive Wire Location: N/A

Key Sense Wire: N/A
Key Sense Wire Location: N/A

Parking Light Negative Wire (-): Brown/White
Parking Light Negative Wire Location: At BCM Module, Plug C2, Pin 5. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors: C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector.

Parking Light Positive Wire (+): Brown
Parking Light Positive Wire Location: At Harness Going To Rear Of Vehicle

Power Door Lock Negative Wire (-): Orange/Black
Power Door Lock Negative Wire Location: At Lock Switch In Drivers Door

Power Door Unlock Negative Wire (-): Orange/Black
Power Door Unlock Negative Wire Location: At Lock Switch In Drivers Door

Door Trigger Negative Wire (-): Gray/Black and Tan/White (Use Both). This vehicle has (2) door pin trigger wires. When connecting to an alarm system, you will need to use both and diode isolate.
Door Trigger Negative Wire Location: At BCM Module, C1, Pins 51 and 53. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors: C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector.

Dome Light Supervision Wire (-): White
Dome Light Supervision Wire Location: At BCM Module, C3, Pin A10. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors: C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector.

Trunk Release Negative Wire (-): Brown/White
Trunk Release Negative Wire Location: At BCM Module, C1, Pin 71. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors: C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector.

Sliding Power Door Wire: N/A
Sliding Power Door Wire Location: N/A

Horn Negative Wire (-): Yellow To Tan
Horn Negative Wire Location: At BCM Module, C2, Pin 14. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors: C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector.

Tachometer Wire Negative Wire (-): White
Tachometer Wire Negative Wire Location: At ECM Module, Blue Plug Pin 48. The ECM module is located in the front passenger fender, remove the wheel to access the panel located behind the wheel. The access panel will let you get to the ECM module.

Wait To Start Wire: N/A
Wait To Start Location: N/A

Brake Light Positive Wire (+): Light Blue
Brake Light Positive Wire Location: At BCM Module, C4, Pin D4. The BCM Module is part of the fuse/relay block on the passenger floor board under the carpet. The BCM Module has these connectors: C1 is a gray 72-pin, C2 is a gray 72-pin, C3 is a red 42-pin, and C4 is a gray 68-pin connector.

Factory Alarm Disarm Wire (-): Disarms With Factory Remote Only
Factory Alarm Disarm Wire Location: N/A

Factory Anti-Theft System: N/A
Factory Anti-Theft System Location: N/A

The 2006 Chevrolet Corvette alarm wire color and location information above is updated as it is submitted by the Modified Life community.

Leave a Reply

Your email address will not be published.

six − 2 =