2004 Jeep Liberty Alarm Wires
Find the right alarm wire colors, locations, and polarity with this 2004 Jeep Liberty alarm wiring diagram. This will help you install your car alarm wiring correctly.
Application | Wire Color and Location |
---|---|
Battery Constant 12v+ Positive Wire (+) | Pink/Black and Red |
Battery Constant 12v+ Positive Wire Location | Ignition Switch Harness |
Starter Positive Wire (+) | Yellow |
Starter Positive Wire Location | Ignition Switch Harness |
Ignition Positive Wire (+) | Red/Dark Blue |
Ignition Positive Wire Location | Ignition Switch Harness |
Accessory Positive Wire (+) | Black/Orange |
Accessory Positive Wire Location | Ignition Switch Harness |
Second Accessory Positive Wire (+) | Black/White |
Second Accessory Positive Wire Location | Ignition Switch Harness |
2004 Jeep Liberty Alarm Sensor Wires
Find the right alarm sensor wire colors, locations, and polarity with this 2004 Jeep Liberty alarm sensor wire chart. This will help you connect all your car alarm sensors correctly.
Application | Wire Color and Location |
---|---|
Parking Light Negative Wire (-) | Light Green/Orange (The parking lights require a negative through a 1000 ohm resistor and an relay to connect.) |
Parking Light Negative Wire Location | At Headlight Switch or BCM Gray 22 Pin, Pin 5. The BCM (body control module) is attached to the left of the fuse box. |
Parking Light Positive Wire (+) | Do Not Use |
Parking Light Positive Wire Location | N/A |
Power Door Lock Negative Wire (-) | Pink/Purple (1-Wire Door Lock System). To lock requires a negative through a 1400 ohm resistor and unlock requires a negative through a 426 ohm resistor, some units will also require 2 extra relays to connect. |
Power Door Lock Negative Wire Location | At Rear Of Fuse Box, Top Left Plug, Pin 14 |
Power Door Unlock Negative Wire (-) | Same Wire as Above |
Power Door Unlock Negative Wire Location | N/A |
Door Trigger Negative Wire (-) | The drivers door is a tan (-) in the gray 26-pin plug, pin 4, the passenger door is a tan/red (-) in the gray 26-pin plug, pin 5, the drivers rear door is a tan/orange (-) in the gray 22-pin plug, pin 3, the passenger rear door (-) is a tan/yellow (-) is a tan/yellow (-) in the gray 26-pin plug, pin 22. When connecting to an alarm system use all 4 door trigger wires and diode isolate. |
Door Trigger Negative Wire Location | At BCM. The BCM (body control module) is attached to the left of the fuse box. |
Dome Light Supervision Wire | Yellow (-), Requires Relay |
Dome Light Supervision Wire Location | At Rear Of Fuse Box, Top Left Plug, Pin 30 |
Trunk Release Negative Wire (-) | Orange/Pink |
Trunk Release Negative Wire Location | At BCM, Gray 26-Pin Plug, Pin 17. The BCM (body control module) is attached to the left of the fuse box. |
Horn Negative Wire (-) | Black/Red |
Horn Negative Wire Location | At Horn Switch |
Tachometer Wire Negative Wire (-) | Any Wire Not Dark Green/Orange |
Tachometer Wire Negative Wire Location | At Any Fuel-Injector Or Ignition Coil |
Brake Light Positive Wire (+) | White/Tan |
Brake Light Positive Wire Location | At Switch Above Brake Pedal |
Factory Alarm Disarm Wire (-) | Light Green/Orange (The disarm wire requires a negative through a 473 ohm resistor and an extra relay.) |
Factory Alarm Disarm Wire Location | At BCM, Gray 22-Pin Plug, Pin 9. The BCM (body control module) is attached to the left of the fuse box. |
Factory Anti-Theft System | Chrysler’s Sentry Key, A Transponder System |
Factory Anti-Theft System Location | Transponder At Ignition Switch Tumbler |
Feel free to use any 2004 Jeep Liberty alarm wiring diagram that is listed here but keep in mind that all information here is provided as is without any warranty of any kind. Use of this 2004 Jeep Liberty car alarm wire chart is at your own risk. Always verify all wires, wire colors and connection points before applying any information found here to your 2004 Jeep Liberty.