Whether your an expert Mercury car alarm installer, Mercury performance fan or a novice Mercury enthusiast with a 2000 Mercury Villager, a Mercury car alarm wiring diagram can save yourself a lot of time. One of the most time consuming tasks with installing an after market car alarm, car security, car remote start, automatic remote starter, shock sensor, tilt sensor, car alarm sensor or any auto alarm is identifying the correct color car security wires for a 2000 Mercury Villager headlight bulb size you need for your low beam or high beam and save time. Also, find your other car light bulb sizes including your fog light, reverse light, turn signal, brake light and more. It’s that easy!
The Modified Life staff has taken all its Mercury car alarm wiring diagrams, Mercury car security wiring diagrams, Mercury car alarm wire diagrams, Mercury car security wiring schematics, Mercury car security diagrams, Mercury remote starter wiring diagrams and cataloged them online for our visitors to use for free. Our automotive wiring diagrams allow you to enjoy your new auto security electronics rather than spend countless hours trying to figure out which wires goes where.
Feel free to use any Mercury auto alarm wiring diagram that is listed on Modified Life but keep in mind that all information here is provided “as is” without any warranty of any kind and most of the auto security wiring diagrams listed on our enthusiast website are submitted by the Modified Life community. Use of the wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your 2000 Mercury Villager.
Request a Car Alarm Wiring Diagram
If you can’t find your car alarm wire diagram, car security wire diagram or auto alarm wire diagram on Modified Life, please feel free to post a car wiring diagram request (Alarm Wiring Diagram Request Page) and we’ll do our best to find you the information you need for your auto alarm or security installation.
Adding More Information
If you would like to help the Modified Life community by adding a car security wire schematic, car alarm wire diagram, car remote starter wire diagram, auto remote starter wire diagram or auto security wire diagram to our resource, please feel free to post any additional car wiring information about the 2000 Mercury Villager on this page.
2000 Mercury Villager Car Alarm Wiring Diagram
Battery Constant 12v+ Positive Wire (+): White/Red
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness
Starter Positive Wire (+): Black/Yellow
Starter Positive Wire Location: Ignition Switch Harness
Second Starter Positive Wire (+): Black/Green
Second Starter Positive Wire Location: Ignition Switch Harness
Ignition Positive Wire (+): Black/White
Ignition Positive Wire Location: Ignition Switch Harness
Accessory Positive Wire (+): Blue
Accessory Positive Wire Location: Ignition Switch Harness
Second Accessory Positive Wire (+): Red
Second Accessory Positive Wire Location: Ignition Switch Harness
Parking Light Negative Wire (-): Gray/Red
Parking Light Negative Wire Location: At Headlight Switch
Power Door Lock Negative Wire (-): Red
Power Door Lock Negative Wire Location: In Either Door Harness
Power Door Unlock Negative Wire (-): Red/Black (Requires a Double Pulse)
Power Door Unlock Negative Wire Location: In Either Door Harness
Door Trigger Negative Wire (-): In the drivers kick panel use the red (-) for the drivers door and for the rear liftgate use the red/white (-), for the passenger door use the red/white (-) and the red/green (-) for the sliding door these wires are in the passenger kick panel. When connecting to an alarm system, use all 4 door trigger wires and diode isolate each trigger wire.
Door Trigger Negative Wire Location: In Each Kick Panel
Dome Light Supervision Wire: Brown/White (-), Requires Part #R30-H Relay
Dome Light Supervision Wire Location: Low In Drivers Kick Panel
Horn Negative Negative Wire (-): Light Blue/Black
Horn Negative Negative Wire Location: At Steering Column Harness
Tachometer Wire Negative Wire (-): White
Tachometer Wire Negative Wire Location: At PCM (Pin 2). The PCM (powertrain control module) is located behind the glovebox.
Brake Light Positive Wire (+): Yellow/Black
Brake Light Positive Wire Location: At Switch Above Brake Pedal
Factory Alarm Disarm Wire (-): Disarms With Unlock, Single Pulse Disarms
Factory Alarm Disarm Wire Location: Disarms With Unlock, Single Pulse Disarms
Anti Theft Type: N/A
ECM Module Location: N/A
BCM Module Location: N/A