1997 Nissan 240SX Alarm Wires
Find the right alarm wire colors, locations, and polarity with this 1997 Nissan 240SX alarm wiring diagram. This will help you install your car alarm wiring correctly.
Application | Wire Color and Location |
---|---|
Battery Constant 12v+ Positive Wire (+) | White |
Battery Constant 12v+ Positive Wire Location | Ignition Switch Harness |
Starter Positive Wire (+) | Black/Yellow (When installing a remote starter, you must use both starter #1 and starter #2 wires. Both wires must be connected to the starter/cranking output wire from the remote starter or the vehicle will not remote start when the engine is cold.) |
Starter Positive Wire Location | Ignition Switch Harness |
Secondary Starter Positive Wire (+) | Black/White (When installing a remote starter, you must use both starter #1 and starter #2 wires. Both wires must be connected to the starter/cranking output wire from the remote starter or the vehicle will not remote start when the engine is cold.) |
Secondary Starter Positive Wire Location | Ignition Switch Harness |
Ignition Positive Wire (+) | Black/Red |
Ignition Positive Wire Location | Ignition Switch Harness |
Accessory Positive Wire (+) | White (When installing a remote starter to this vehicle, an extra relay is needed to isolate the accessory wire.) |
Accessory Positive Wire Location | Ignition Switch Harness |
1997 Nissan 240SX Alarm Sensor Wires
Find the right alarm sensor wire colors, locations, and polarity with this 1997 Nissan 240SX alarm sensor wire chart. This will help you connect all your car alarm sensors correctly.
Application | Wire Color and Location |
---|---|
Parking Light Positive Wire (+) | Red/Blue |
Parking Light Positive Wire Location | At Steering Column Harness |
Power Door Lock Negative Wire (-) | Light Green/White |
Power Door Lock Negative Wire Location | At Anti-Theft Module. When installing a remote starter, you must use both starter #1 and starter #2 wires. Both wires must be connected to the starter/cranking output wire from the remote starter or the vehicle will not remote start when the engine is cold. |
Power Door Unlock Negative Wire (-) | Brown |
Power Door Unlock Negative Wire Location | At Anti-Theft Module. When installing a remote starter, you must use both starter #1 and starter #2 wires. Both wires must be connected to the starter/cranking output wire from the remote starter or the vehicle will not remote start when the engine is cold. |
Door Trigger Negative Wire (-) | Red/White |
Door Trigger Negative Wire Location | In Drivers Kick Panel |
Dome Light Supervision Wire | Use Door Trigger (Requires Relay) |
Dome Light Supervision Wire Location | N/A |
Horn Negative Negative Wire (-) | Yellow/Green |
Horn Negative Negative Wire Location | At Anti-Theft Module. The anti-theft module is located just above hood release cable, in the drivers kick panel. |
Tachometer Wire Negative Wire (-) | Yellow/Red |
Tachometer Wire Negative Wire Location | At ECM, In Passenger Kick Panel |
Brake Light Positive Wire (+) | Red/Green |
Brake Light Positive Wire Location | At Switch Above Brake Pedal |
Factory Alarm Disarm Wire (-) | Green/Yellow |
Factory Alarm Disarm Wire Location | At Anti-Theft Module. When installing a remote starter, you must use both starter #1 and starter #2 wires. Both wires must be connected to the starter/cranking output wire from the remote starter or the vehicle will not remote start when the engine is cold. |
Factory Anti-Theft Wire (-) | N/A |
Factory Anti-Theft Wire Location | N/A |
Feel free to use any 1997 Nissan 240SX alarm wiring diagram that is listed here but keep in mind that all information here is provided as is without any warranty of any kind. Use of this 1997 Nissan 240SX car alarm wire chart is at your own risk. Always verify all wires, wire colors and connection points before applying any information found here to your 1997 Nissan 240SX.