MODIFIEDLIFE

1993 Toyota Camry Car Security Wiring Diagram

1993 Toyota Camry Alarm Wires

Find the right alarm wire colors, locations, and polarity with this 1993 Toyota Camry alarm wiring diagram. This will help you install your car alarm wiring correctly.

Application Wire Color and Location
Battery Constant Power 12v+ Wire (+) White/Red
Battery Constant Power 12v+ Wire Location At Ignition Switch Harness
Ignition Wire (+) Black/Yellow
Ignition Wire Location At Ignition Switch Harness
Second Ignition Wire (+) Black/Orange
Second Ignition Wire Location At Ignition Switch Harness
Accessory Wire (+) Pink/Blue
Accessory Wire Location At Ignition Switch Harness
Second Accessory Wire (+) N/A
Second Accessory Wire Location N/A
Starter Wire (+) Black/White
Starter Wire Location At Ignition Switch Harness
Second Starter Wire (+) N/A
Second Starter Wire Location At Ignition Switch Harness
Ground Wire Chassis

1993 Toyota Camry Alarm Sensor Wires

Find the right alarm sensor wire colors, locations, and polarity with this 1993 Toyota Camry alarm sensor wire chart. This will help you connect all your car alarm sensors correctly.

Application Wire Color and Location
Brake Light Wire (+) Green/White
Brake Light Wire Location At the bottom of the fuse box.
Dome Light Supervision Wire Use Door Trigger (Requires Relay)
Dome Light Supervision Wire Location N/A
Door Trigger Wire (+) Red/White
Door Trigger Wire Location To find this door trigger wire, remove the black plastic air duct covering the top right side of the fuse box. This will let you access the 6-pin plug that contains this red/white wire (-).
Hood Pin Switch Wire (-) N/A
Hood Pin Switch Wire Location N/A
Horn Wire (-) Green/Black
Horn Wire Location At the steering column wire harness.
Key Sense Wire (+) N/A
Key Sense Wire Location N/A
Parking Light Wire (-) Green
Parking Light Wire Location At Headlight Switch
Power Door Lock Wire (-) Blue/White
Power Door Lock Wire Location At blue plug in passenger kick panel.
Power Door Unlock Wire (-) Light Green/Red
Power Door Unlock Wire Location At blue plug in passenger kick panel.
Tachometer Wire (-) Black
Tachometer Wire Location At the Check Connector. On the 4-cylinder engine, the black wire is at the check connector located on the rear of the passenger strut tower. On the V6 engine, the black wire is at the ignitor located on the drivers side strut tower.
Trunk Pin Switch Wire (-) N/A
Trunk Pin Switch Wire Location N/A
Trunk Release Wire (+) N/A
Trunk Release Wire Location N/A
Wait to Start Light Wire (-) N/A
Wait to Start Light Wire Location N/A
Factory Alarm Arm Wire (-) N/A
Factory Alarm Arm Wire Location N/A
Factory Alarm Disarm Wire (-) N/A
Factory Alarm Disarm Wire Location N/A
Factory Anti-Theft System N/A
Factory Anti-Theft System Location N/A
Factory Immobilizer Bypass N/A

Feel free to use any 1993 Toyota Camry alarm wiring diagram that is listed here but keep in mind that all information here is provided as is without any warranty of any kind. Use of this 1993 Toyota Camry car alarm wire chart is at your own risk. Always verify all wires, wire colors and connection points before applying any information found here to your 1993 Toyota Camry.

6 thoughts on “1993 Toyota Camry Car Security Wiring Diagram”

  1. Sherry, it sounds like your 1993 Toyota Camry alarm shock sensor is too sensitive. You need to lower the shocks sensor sensitivity to prevent you alarm from going off when cars drive by. Some alarm systems have external shock sensors which can be adjusted externally. Some alarm systems have built in shock sensors which can only be adjusted via alarm programming. If you have never adjusted or programmed your alarm system before, our advice is that you take your car to an experienced alarm installer. It should not take more than 30 minutes from start to finish to adjust it. Hope this helps. Good luck with your 1993 Toyota Camry shock sensor adjustment.

  2. Grace, as much as we would like to help you, not all car alarms are installed the same way. Different brands and different setups will call for different wiring. Our advice is to take your car to a qualified alarm installer and ask them to remove the alarm because it does take some wiring knowledge and experience to know what to remove. Hope this helps. Good luck on your alarm removal.

  3. I have a 93 Toyota Celica GT, & our alarm buttom for the key ring was smashed in our tractor gears & we don’t have another one. How do you disarm this alarm. I believe it came from the factory this way along with several other special items on the car. We were the second owners & we have had it for 11 years. I have tried to remove the fuse for the horn to disarm it but to no avail. Could you please help me with this please.

  4. Wired a Boss remote starter / car alarm with ease with the wiring specs. everything spot on. Nice because this car doesnt have the security wire and I didnt have to get a key wired. No resistors for trunk unlock. Nice!!

    Good job

Leave a Comment

Your email address will not be published. Required fields are marked *