2012 Jeep Liberty Alarm Wires
Find the right alarm wire colors, locations, and polarity with this 2012 Jeep Liberty alarm wiring diagram. This will help you install your car alarm wiring correctly.
Application | Wire Color and Location |
---|---|
Battery Constant 12v+ Positive Wire (+) | Blue/Red (This wire only supplies 10 amps of current, for high current application go directly to the battery.) |
Battery Constant 12v+ Positive Wire Location | Ignition Switch Harness |
Starter Positive Wire (+) | Yellow/Gray (Not for Remote Start) |
Starter Positive Wire Location | Ignition Switch Harness |
Second Starter Positive Wire (+) | Violet/Brown (This wire is also the key sense and accessory wire, use a 180 ohm resistor for second start for remote start.) |
Second Starter Positive Wire Location | Ignition Switch Harness |
Ignition Positive Wire (+) | Pink/White |
Ignition Positive Wire Location | Ignition Switch Harness |
Second Ignition Positive Wire (+) | N/A |
Second Ignition Positive Wire Location | N/A |
Third Ignition Positive Wire (+) | N/A |
Third Ignition Positive Wire Location | N/A |
Accessory Positive Wire (+) | Violet/Brown (This wire is also the key sense and second starter wire, use a 580 ohm resistor for second accessory for remote start.) |
Accessory Positive Wire Location | Ignition Switch Harness |
Second Accessory Positive Wire (+) | N/A |
Second Accessory Positive Wire Location | N/A |
Key Sense Wire | Violet/Brown |
Key Sense Wire Location | Ignition Switch Harness |
2012 Jeep Liberty Alarm Sensor Wires
Find the right alarm sensor wire colors, locations, and polarity with this 2012 Jeep Liberty alarm sensor wire chart. This will help you connect all your car alarm sensors correctly.
Application | Wire Color and Location |
---|---|
Parking Light Negative Wire (-) | N/A |
Parking Light Negative Wire Location | N/A |
Parking Light Positive Wire (+) | White/Violet |
Parking Light Positive Wire Location | At Harness in Driver Kick Panel |
Power Door Lock Negative Wire (-) | Violet/Dark Green (Lock is (-) through a 330 ohm resistor. Must use relay.) |
Power Door Lock Negative Wire Location | In Harness in Driver Kick Panel |
Power Door Unlock Negative Wire (-) | Violet/Dark Green (Unlock is (-) through a 100 ohm resistor. Must use relay.) |
Power Door Unlock Negative Wire Location | In Harness in Driver Kick Panel |
Door Trigger Negative Wire (-) | Use all door triggers and diode isolate each wire. |
Door Trigger Negative Wire Location | At each door |
Dome Light Supervision Wire (-) | Yellow/White |
Dome Light Supervision Wire Location | In Harness in Driver Kick Panel |
Trunk Trigger Negative Wire (-) | Violet/Orange |
Trunk Trigger Negative Wire Location | In Harness in Driver Kick Panel |
Trunk Release Negative Wire (-) | N/A |
Trunk Release Negative Wire Location | N/A |
Sliding Power Door Wire | N/A |
Sliding Power Door Wire Location | N/A |
Horn Negative Wire (-) | Dark Green/Violet |
Horn Negative Wire Location | In Harness at Steering Column |
Tachometer Wire Negative Wire (-) | N/A |
Tachometer Wire Negative Wire Location | N/A |
Wait To Start Wire | N/A |
Wait To Start Location | N/A |
Brake Light Positive Wire (+) | White/Tan |
Brake Light Positive Wire Location | At Switch Above the Brake Pedal |
Factory Alarm Arm Wire (-) | N/A |
Factory Alarm Arm Wire Location | N/A |
Factory Alarm Disarm Wire (-) | N/A |
Factory Alarm Disarm Wire Location | N/A |
Factory Anti-Theft System | Daimler Sentry Key Vehicle Immobilizer |
Factory Anti-Theft System Location | Key Sends RF Signal to the BCM Module |
Feel free to use any 2012 Jeep Liberty alarm wiring diagram that is listed here but keep in mind that all information here is provided as is without any warranty of any kind. Use of this 2012 Jeep Liberty car alarm wire chart is at your own risk. Always verify all wires, wire colors and connection points before applying any information found here to your 2012 Jeep Liberty.