2010 Ford Fusion Car Stereo Installation Instructions

2010 Ford Fusion Car Stereo Installation Instructions

Whether your an expert Ford Fusion mobile electronics installer, Ford Fusion fanatic, or a novice Ford Fusion enthusiast with a 2010 Ford Fusion, a car stereo wiring diagram can save yourself a lot of time. Automotive wiring in a 2010 Ford Fusion vehicles are becoming increasing more difficult to identify due to the installation of more advanced factory oem electronics.

One of the most time consuming tasks with installing an after market car stereo, car radio, satellite radio, xm radio, car speakers, tweeters, car subwoofer, crossovers, audio equalizer, car amplifier, mobile amp, car amplifier, mp3 player, ipod or any car audio electronics is identifying the correct color car audio wires for your 2010 Ford Fusion.

The Modified Life staff has taken all its Ford Fusion car radio wiring diagrams, Ford Fusion car audio wiring diagrams, Ford Fusion car stereo wiring diagrams, Ford Fusion car radio wiring schematics, Ford Fusion car wiring diagrams and cataloged them online for use by our visitors for free. Our automotive wiring diagrams allow you to enjoy your new mobile electronics rather than spend countless hours trying to figure out which wires goes to which 2010 Ford Fusion part or component.

Feel free to use any Ford Fusion car stereo wiring diagram that is listed on Modified Life but keep in mind that all information here is provided “as is” without any warranty of any kind and most of the car audio wiring diagrams listed on our enthusiast website are submitted by the Modified Life community. Use of the Ford Fusion wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your 2010 Ford Fusion.

Questions

If you have any questions pertaining to the audio system in the 2010 Ford Fusion, please feel free to post it at the bottom of this page and either we’ll do our best to find you the information you need or hopefully someone in the Modified Life community will have the information you’re looking for.

Request a Car Stereo Wiring Diagram

If you can’t find a particular car audio wire diagram on Modified Life, please feel free to post a car radio wiring diagram request at the bottom of this page and we’ll do our best to find you the diagram or schematic you need for your mobile audio installation.

Adding More Information

If you would like to help the Modified Life community by adding any missing information or adding a new car audio wire diagram to our resource, please feel free to contact us at: contact form or post it at the bottom of this page.

2010 Ford Fusion Car Stereo Installation Instructions

Car Radio Battery Constant 12v+ Wire: White/Red
Car Radio Accessory Switched 12v+ Wire: N/A
Car Radio Ground Wire: Black/Blue
Car Radio Illumination Wire: N/A
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger Wire: Yellow/Green
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): White
Left Front Speaker Negative Wire (-): White/Brown
Right Front Speaker Positive Wire (+): White/Violet
Right Front Speaker Negative Wire (-): White/Orange
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): White/Green
Left Rear Speaker Negative Wire (-): Brown/Yellow
Right Rear Speaker Positive Wire (+): Brown/White
Right Rear Speaker Negative Wire (-): Brown/Blue

The 2010 Ford Fusion radio wire color information above is updated as it is submitted by the Modified Life community.


4 Replies to “2010 Ford Fusion Car Stereo Installation Instructions”

  1. Does my 2010 Ford fusion se have a oem amplifier and if where is it located? I do not have the Sony upgrade. Anyone?

  2. Hi I have a 2010 ford fusion I just installed a pioneer avh-p2400bt and I was wondering where I would run the power wire for my amps don’t see any grommets on the firewall

  3. Nicholas, most vehicles have a factory hole with a rubber or plastic grommet at the firewall. This is usually the standard place to run a power wire through the firewall. If one of these holes are not available or not large enough, a hole will have to be drilled to accommodate your power wire. Choose something on the engine side of the firewall as reference and try to match it up on the interior side of the firewall. This will make sure you do not drill through anything important. Then drill a hole somewhere near or beside your reference point. Make sure to use a firewall grommet to prevent the power wire from chaffing on the firewall that could potentially cause a short. Hope this helps. Good luck with your 2010 Ford Fusion amplifier installation.

Leave a Reply

Your email address will not be published. Required fields are marked *

20 − three =