2007 Chrysler 300 Car Audio Wiring Diagram

Whether your an expert Chrysler 300 mobile electronics installer, Chrysler 300 fanatic, or a novice Chrysler 300 enthusiast with a 2007 Chrysler 300, a car stereo wiring diagram can save yourself a lot of time. Automotive wiring in a 2007 Chrysler 300 vehicles are becoming increasing more difficult to identify due to the installation of more advanced factory oem electronics.

One of the most time consuming tasks with installing an after market car stereo, car radio, satellite radio, xm radio, car speakers, tweeters, car subwoofer, crossovers, audio equalizer, car amplifier, mobile amp, car amplifier, mp3 player, ipod or any car audio electronics is identifying the correct color car audio wires for your 2007 Chrysler 300.

The Modified Life staff has taken all its Chrysler 300 car radio wiring diagrams, Chrysler 300 car audio wiring diagrams, Chrysler 300 car stereo wiring diagrams, Chrysler 300 car radio wiring schematics, Chrysler 300 car wiring diagrams and cataloged them online for use by our visitors for free. Our automotive wiring diagrams allow you to enjoy your new mobile electronics rather than spend countless hours trying to figure out which wires goes to which 2007 Chrysler 300 part or component.

Feel free to use any Chrysler 300 car stereo wiring diagram that is listed on Modified Life but keep in mind that all information here is provided “as is” without any warranty of any kind and most of the car audio wiring diagrams listed on our enthusiast website are submitted by the Modified Life community. Use of the Chrysler 300 wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your 2007 Chrysler 300.

Questions

If you have any questions pertaining to the audio system in the 2007 Chrysler 300, please feel free to post it at the bottom of this page and either we’ll do our best to find you the information you need or hopefully someone in the Modified Life community will have the information you’re looking for.

Request a Car Stereo Wiring Diagram

If you can’t find a particular car audio wire diagram on Modified Life, please feel free to post a car radio wiring diagram request at the bottom of this page and we’ll do our best to find you the diagram or schematic you need for your mobile audio installation.

Adding More Information

If you would like to help the Modified Life community by adding any missing information or adding a new car audio wire diagram to our resource, please feel free to post it at the bottom of this page.

2007 Chrysler 300 Car Audio Wiring Diagram

Car Radio Battery Constant 12v+ Wire: Gray/Light Green
Car Radio Accessory Switched 12v+ Wire: The radio harness does not provide a switched power source. Run a wire to the fusebox for switched power.
Car Radio Ground Wire: Black/Light Green
Car Radio Illumination Wire: N/A
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: N/A
Car Audio Front Speakers Location: N/A
Left Front Speaker Positive Wire (+): Gray/Violet
Left Front Speaker Negative Wire (-): Gray/Yellow
Right Front Speaker Positive Wire (+): Dark Green/Violet
Right Front Speaker Negative Wire (-): Dark Green/Yellow
Car Audio Rear Speakers Size: N/A
Car Audio Rear Speakers Location: N/A
Left Rear Speaker Positive Wire (+): Dark Green/Tan
Left Rear Speaker Negative Wire (-): Dark Green/Gray
Right Rear Speaker Positive Wire (+): Dark Green/Brown
Right Rear Speaker Negative Wire (-): Yellow/Green

Make Your Chrysler 300 Car Stereo Installation Easy with these Products

9 Comments

  • Reply Anthony Caley July 19, 2008 at 7:52 pm

    I have a 2007 Chrysler 300C.

    I want to install an external Sirius radio that I can move between my vehicles. I want to connect the Sirius radio to the cars radio power source so that they turn off together.

    Right now, the Sirius is connected a non-switched power source.

    Do you know where I can access the radio/accessory power without tearing my car apart?

  • Reply ModifiedLife July 20, 2008 at 12:59 am

    Anthony, use the yellow wire at the PSC/ECU module. It is located on the right side, behind the glove box (Pin 35 of the 40 pin plug connected to the module). Hope this helps. Good luck.

  • Reply GM January 24, 2011 at 11:37 pm

    I have a 2007 Chrysler 300 touring with the premium sound (8 speaker system). I want to install a aftermarket stereo but i am not successful finding the plug in connector so i dont have to cut into factory harness. Please advice. Thank you.

  • Reply ModifiedLife February 1, 2011 at 8:08 pm

    GM, here is the wiring harness you need for your 2007 Chrysler 300 Touring (Premium 8-Speaker System):

    2007 Chrysler 300 Touring Stereo Wiring Harness

    If you’ve never installed car audio before, we advise you to take your car to an experienced mobile audio installer. Hope this helps. Good luck with your for 2007 Chrysler 300 Touring stereo installation.

  • Reply jr March 9, 2011 at 6:01 pm

    i have a 2007 Chrysler 300 touring, i was wondering if its required to get the 12v switch from the fuse box or is there any other way that i can get it from any other place…

  • Reply ModifiedLife March 15, 2011 at 1:03 am

    Jr, run a primary wire to the steering column and use the violet/brown wire in the ignition switch harness for a switched power source. Hope this helps. Good luck with your 2007 Chrysler 300 stereo installation.

  • Reply jess November 17, 2011 at 2:06 pm

    does the 2007 Chrysler 300 radio have rca connectors in the back?

  • Reply ModifiedLife November 29, 2011 at 5:23 pm

    Jess, most late model vehicles do not have RCA outputs on the factory radio to feed an audio signal to your aftermarket amplifier. You would have to install a line out converter to supply an audio output. Here is the Line-Out Converter you need:

    Speaker to RCA Line Out Converter

    When splicing in the RCA Line Out Converter, tap your factory rear speaker wires to get a full range audio source. We suggest you invest in some solid wire taps that wont come loose. These wire tap connectors will allow you to tap into wires without cutting and installs in seconds by hand with no crimping or tools required. If you install a line out converter, your rear speakers will still work properly. If you’ve never installed car audio before, we advise you to take your car to an experienced mobile audio installer. Hope this helps. Good luck with your 2007 Chrysler 300 amplifier installation.

  • Reply Joel January 8, 2012 at 5:56 pm

    I have a 2007 Chrysler 300 with Boston premium sound. Question is how can I use the factory amp to get sound. I have connected the harness matching the colors but no sound is coming out. Please help, I was told I can run the remote wire directly to the amp and this would work, no modules or interfaces needed. System i am trying to install is a Pioneer AVIC-D3. Anyone know the 2007 Chrysler 300 amplifier turn on wire? Thank you in advance.

  • Leave a Reply

    20 + 4 =