Whether your an expert Oldsmobile Bravada car alarm installer, Oldsmobile Bravada performance fan or a novice Oldsmobile Bravada enthusiast with a 2001 Oldsmobile Bravada, a Oldsmobile Bravada car alarm wiring diagram can save yourself a lot of time. One of the most time consuming tasks with installing an after market car alarm, car security, car remote start, automatic remote starter, shock sensor, tilt sensor, car alarm sensor or any auto alarm is identifying the correct color car security wires for a 2001 Oldsmobile Bravada.

The Modified Life staff has taken all its Oldsmobile Bravada car alarm wiring diagrams, Oldsmobile Bravada car security wiring diagrams, Oldsmobile Bravada car alarm wire diagrams, Oldsmobile Bravada car security wiring schematics, Oldsmobile Bravada car security diagrams, Oldsmobile Bravada remote starter wiring diagrams and cataloged them online for our visitors to use for free. Our automotive wiring diagrams allow you to enjoy your new auto security electronics rather than spend countless hours trying to figure out which wires goes where.

Feel free to use any Oldsmobile Bravada auto alarm wiring diagram that is listed on Modified Life but keep in mind that all information here is provided “as is” without any warranty of any kind and most of the auto security wiring diagrams listed on our enthusiast website are submitted by the Modified Life community. Use of the wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your 2001 Oldsmobile Bravada.

Questions

If you have any questions pertaining to the car wiring in a 2001 Oldsmobile Bravada, please feel free to post it at the bottom of this page and either we’ll do our best to find you the information you need or hopefully someone in the Modified Life community will have the information you are looking for.

Request a Car Alarm Wiring Diagram

If you can’t find your car alarm wiring, car security wire diagram or auto alarm wire diagram on Modified Life, please feel free to post a car alarm wiring diagram request on this page and we’ll do our best to find you the diagram, schematic or information you need for your mobile security installation.

Adding More Information

If you would like to help the Modified Life community by adding a car security wire schematic, car alarm wire diagram, car remote starter wire diagram, auto remote starter wire diagram or auto security wire diagram to our resource, please feel free to post any additional car wiring information about the 2001 Oldsmobile Bravada on this page.

2001 Oldsmobile Bravada Car Alarm Wiring Guide

Battery Constant 12v+ Positive Wire (+): Red
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Yellow
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Pink
Ignition Positive Wire Location: Ignition Switch Harness

Secondary Ignition Positive Wire (+): White (This wire must be connected as ignition #2 for remote starting.)
Secondary Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Orange
Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Positive Wire (+): Brown
Parking Light Positive Wire Location: At BCM, Light Blue Plug. The BCM (body control module) is located to the right of the gas pedal, attached to the heater box. The BCM has 3 plugs that face the drivers side of the vehicle. On the BCM is printed the colors of the 3 plugs, purple, blue and brown.

Power Door Lock Positive Wire (+): Light Blue
Power Door Lock Positive Wire Location: At BCM, Brown Plug. The BCM (body control module) is located to the right of the gas pedal, attached to the heater box. The BCM has 3 plugs that face the drivers side of the vehicle. On the BCM is printed the colors of the 3 plugs, purple, blue and brown.

Power Door Unlock Positive Wire (+): White
Power Door Unlock Positive Wire Location: At BCM, Brown Plug. The BCM (body control module) is located to the right of the gas pedal, attached to the heater box. The BCM has 3 plugs that face the drivers side of the vehicle. On the BCM is printed the colors of the 3 plugs, purple, blue and brown.

Door Trigger Wire: The drivers door is a tan (-) pin B4, purple plug at the BCM, the passenger door is a orange (-) pin B2 of the purple plug, the rear doors and the rear hatch is a dark blue/white (-) pin B11 in the light blue plug of the BCM. When connecting to an alarm system, use all 3 door trigger wires and diode isolate.
Door Trigger Positive Wire Location: At BCM. The BCM (body control module) is located to the right of the gas pedal, attached to the heater box. The BCM has 3 plugs that face the drivers side of the vehicle. On the BCM is printed the colors of the 3 plugs, purple, blue and brown.

Domelight Supervision Wire (-): Tan
Domelight Supervision Wire Location: At BCM, Purple Plug, Pin B4. The BCM (body control module) is located to the right of the gas pedal, attached to the heater box. The BCM has 3 plugs that face the drivers side of the vehicle. On the BCM is printed the colors of the 3 plugs, purple, blue and brown.

Trunk Release Negative Wire (-): Black
Trunk Release Negative Wire Location: At BCM, Purple Plug. The BCM (body control module) is located to the right of the gas pedal, attached to the heater box. The BCM has 3 plugs that face the drivers side of the vehicle. On the BCM is printed the colors of the 3 plugs, purple, blue and brown.

Horn Negative Negative Wire (-): Black
Horn Negative Negative Wire Location: At BCM, Brown Plug. The BCM (body control module) is located to the right of the gas pedal, attached to the heater box. The BCM has 3 plugs that face the drivers side of the vehicle. On the BCM is printed the colors of the 3 plugs, purple, blue and brown.

Tachometer Wire Negative Wire (-): White
Tachometer Wire Negative Wire Location: At PCM. The PCM (powertrain control module) is located on the passenger fender.

Brake Light Positive Wire (+): White
Brake Light Positive Wire Location: At Switch Above Brake Pedal

Factory Alarm Disarm Wire (-): Light Green
Factory Alarm Disarm Wire Location: At BCM, Purple Plug. The BCM (body control module) is located to the right of the gas pedal, attached to the heater box. The BCM has 3 plugs that face the drivers side of the vehicle. On the BCM is printed the colors of the 3 plugs, purple, blue and brown.

Factory Anti-Theft Wire: Yellow (+), Orange/Black (-) And Red/White (Not Used)
Factory Anti-Theft Wire Location: GM Passlock 2 System, These Wires Exit The Ignition Switch Tumbler Together And Are In The Main Ignition Switch Harness In The Column.

Make Your Car Alarm Installation Easy with these Tools and Accessories
Save Up to 60% Off Car Alarms and Auto Security