2000 Chrysler Town and Country Car Stereo Wiring Diagram

Whether your an expert Chrysler Town and Country mobile electronics installer, Chrysler Town and Country fanatic, or a novice Chrysler Town and Country enthusiast with a 2000 Chrysler Town and Country, a car stereo wiring diagram can save yourself a lot of time. Automotive wiring in a 2000 Chrysler Town and Country vehicles are becoming increasing more difficult to identify due to the installation of more advanced factory oem electronics.

One of the most time consuming tasks with installing an after market car stereo, car radio, satellite radio, xm radio, car speakers, tweeters, car subwoofer, crossovers, audio equalizer, car amplifier, mobile amp, car amplifier, mp3 player, ipod or any car audio electronics is identifying the correct color car audio wires for your 2000 Chrysler Town and Country.

The Modified Life staff has taken all its Chrysler Town and Country car radio wiring diagrams, Chrysler Town and Country car audio wiring diagrams, Chrysler Town and Country car stereo wiring diagrams, Chrysler Town and Country car radio wiring schematics, Chrysler Town and Country car wiring diagrams and cataloged them online for use by our visitors for free. Our automotive wiring diagrams allow you to enjoy your new mobile electronics rather than spend countless hours trying to figure out which wires goes to which 2000 Chrysler Town and Country part or component.

Feel free to use any Chrysler Town and Country car stereo wiring diagram that is listed on Modified Life but keep in mind that all information here is provided “as is” without any warranty of any kind and most of the car audio wiring diagrams listed on our enthusiast website are submitted by the Modified Life community. Use of the Chrysler Town and Country wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your 2000 Chrysler Town and Country.

Questions

If you have any questions pertaining to the audio system in the 2000 Chrysler Town and Country, please feel free to post it at the bottom of this page and either we’ll do our best to find you the information you need or hopefully someone in the Modified Life community will have the information you’re looking for.

Request a Car Stereo Wiring Diagram

If you can’t find a particular car audio wire diagram on Modified Life, please feel free to post a car radio wiring diagram request at the bottom of this page and we’ll do our best to find you the diagram or schematic you need for your mobile audio installation.

Adding More Information

If you would like to help the Modified Life community by adding any missing information or adding a new car audio wire diagram to our resource, please feel free to post it at the bottom of this page.

2000 Chrysler Town and Country Car Stereo Wiring Diagram

Car Radio Battery Constant 12v+ Wire: Pink
Car Radio Accessory Switched 12v+ Wire: Red/White
Car Radio Ground Wire: Ground or Back Strap
Car Radio Illumination Wire: Black/Yellow
Car Stereo Dimmer Wire: N/A
Car Stereo Antenna Trigger Wire: N/A
Car Stereo Amp Trigger Wire: N/A
Car Stereo Amplifier Location: N/A
Car Audio Front Speakers Size: 5″ x 7″ Speakers
Car Audio Front Speakers Location: Doors
Left Front Speaker Positive Wire (+): Green
Left Front Speaker Negative Wire (-): Brown/Red
Right Front Speaker Positive Wire (+): Purple
Right Front Speaker Negative Wire (-): Blue/Red
Car Audio Rear Speakers Size: 6″ x 9″ Speakers
Car Audio Rear Speakers Location: Side Panels
Left Rear Speaker Positive Wire (+): Brown/Yellow
Left Rear Speaker Negative Wire (-): Brown/Light Blue
Right Rear Speaker Positive Wire (+): Blue/Orange
Right Rear Speaker Negative Wire (-): Blue/White

Make Your Chrysler Town Country Stereo Installation Easy with these Products

15 Comments

  • Reply Ades October 30, 2008 at 6:05 pm

    my father in law has a 2000 town & country van , the 2 left front speakers have a muffled sound coming out of them. sometimes it sounds like popping and snapping. i hooked another speaker up just to see if the speaker was bad. nope same problem. Any ideas???? Thank You

  • Reply ModifiedLife November 4, 2008 at 3:56 pm

    Ades, you may have a faulty factory amplifier in your car that is preventing any production of sound. Our advice would be to have your local Chrysler dealer check out your audio system and find out what the problem might be. Hope this helps. Good luck.

  • Reply paco May 5, 2009 at 11:41 pm

    I have just the same problem, the question is if the amplifier actually inside the car stereo (built-in) or if it’s a separate module, and where is located. thanks.

  • Reply chuy martinez July 16, 2010 at 12:27 pm

    where is the factory stock amp in a 2000 chrysler town and country please help! =o)

  • Reply Eric October 15, 2010 at 12:00 am

    The amps are located on the back of the rear and front door speakers. The front door speaker amps run the dash speakers as well.

  • Reply ModifiedLife October 19, 2010 at 12:57 am

    Eric, thanks for the 2000 Chrysler Town Country stereo amplifier location information contribution!

  • Reply alejandro royas November 20, 2010 at 6:56 pm

    I installed a new stereo on my town & country 2000, but i dont know why the speaker don’t make a sound, can you help me?, thank you.

  • Reply ModifiedLife November 30, 2010 at 7:27 pm

    Alejandro, first double check ALL your fuses and make sure ALL your fuses are good. You can do this by using an Automotive Fuse Tester and making sure all of your fuses are not blown. If all of your fuses are good, your 2000 Chrysler Town Country may have a factory amplifier that needs to be turned on by your after market radio. The car stereo amplifier trigger wire has to be wired up to turn on your factory amplifier to output sound from your speakers. Hope this points you in the right direction. Good luck with your 2000 Chrysler Town Country stereo installation.

  • Reply ed March 24, 2011 at 9:37 am

    finally got it to work, I had to hook up the ground wires and the strap wire together and also the blue antenna wire on the head unit to the last wire on the black connector opposite small key tang, I guess the other two wire connector is for the cd changer if used and also has something to do with the steering

  • Reply ModifiedLife March 29, 2011 at 3:04 am

    Ed, thanks for the 2000 Chrysler Town Country stereo wiring information contribution!

  • Reply Mke April 11, 2011 at 7:24 am

    My 2000 T & C LE has a BASE Machine Gun sounding noise coming from the the passenger side dash and door speaker. The speaker controls will not cut the speakers off. I can hear normal music or talk from the other spearkers, driver side and read, but they seem muffled. could this be a radio or a wiring issue. One speaker – replace it. But two speakers going out at the time points to something else. Any ideas?

  • Reply Randy April 29, 2011 at 8:40 pm

    I just replaced the radio/cassette/CD player in my 2000 Town & Country. Removal and replacement went pretty smoothly. After connecting the new unit (wire for wire) and reinserting it, everything turns on and appears to function, except for one thing–all the radio stations are static. When I manually tune to a station, AM or FM, I get nothing but static/snow. I’m guessing it’s an antenna problem of some sort. Looks like I’m going to have to take it out again to see what could be wrong, but I DO know that I reconnected everything, the antenna included. Is there something I’m not doing right? Might I have forgotten to do something when I reconnected and reinserted the unit?

  • Reply ModifiedLife May 3, 2011 at 1:43 am

    Randy, the antenna wire may be plugged into the rear of your 2000 Chrysler Town Country but your vehicle may also have powered antenna that needs to be turned on. We currently do not have any information on the 2000 Chrysler Town Country antenna turn-on wiring but hopefully someone from our Modified Life community would be able to chime in and help you out.

  • Reply Billy December 31, 2012 at 1:15 pm

    Changed the radio out with an identical factory radio out of a neon into my 2001 Chrysler Town and Country. Everything installed and plugged up the same way and it all works but there is no sound. Is there something else I need to do to get sound? Thanks

  • Reply ModifiedLife January 21, 2013 at 11:09 pm

    Billy, first double check ALL your fuses and make sure ALL your fuses are good. You can do this by using an Automotive Fuse Tester and making sure all of your fuses are not blown. If all of your fuses are good, your 2000 Chrysler Town Country may have a factory amplifier that needs to be turned on by your after market radio. The car radio amplifier trigger wire has to be wired up to turn on your factory amp to output sound from your speakers. Hope this points you in the right direction. Good luck with your 2000 Chrysler Town Country stereo install.

  • Leave a Reply

    4 + 12 =