MODIFIEDLIFE

1998 Chrysler LHS Auto Alarm Wiring Diagram


Whether your an expert Chrysler LHS car alarm installer, Chrysler LHS performance fan or a novice Chrysler LHS enthusiast with a 1998 Chrysler LHS, a Chrysler LHS car alarm wiring diagram can save yourself a lot of time. One of the most time consuming tasks with installing an after market car alarm, car security, car remote start, automatic remote starter, shock sensor, tilt sensor, car alarm sensor or any auto alarm is identifying the correct color car security wires for a 1998 Chrysler LHS headlight bulb size you need for your low beam or high beam and save time. Also, find your other car light bulb sizes including your fog light, reverse light, turn signal, brake light and more. It’s that easy!

The Modified Life staff has taken all its Chrysler LHS car alarm wiring diagrams, Chrysler LHS car security wiring diagrams, Chrysler LHS car alarm wire diagrams, Chrysler LHS car security wiring schematics, Chrysler LHS car security diagrams, Chrysler LHS remote starter wiring diagrams and cataloged them online for our visitors to use for free. Our automotive wiring diagrams allow you to enjoy your new auto security electronics rather than spend countless hours trying to figure out which wires goes where.

Feel free to use any Chrysler LHS auto alarm wiring diagram that is listed on Modified Life but keep in mind that all information here is provided “as is” without any warranty of any kind and most of the auto security wiring diagrams listed on our enthusiast website are submitted by the Modified Life community. Use of the wiring information is at your own risk. Always verify all wires, wire colors and diagrams before applying any information found here to your 1998 Chrysler LHS.

Questions

If you have any questions pertaining to the car wiring in a 1998 Chrysler LHS, please feel free to post it at the bottom of this page and either we’ll do our best to find you the information you need or hopefully someone in the Modified Life community will have the information you are looking for.

Request a Car Alarm Wiring Diagram

If you can’t find your car alarm wiring, car security wire diagram or auto alarm wire diagram on Modified Life, please feel free to post a car alarm wiring diagram request on this page and we’ll do our best to find you the diagram, schematic or information you need for your mobile security installation.

Adding More Information

If you would like to help the Modified Life community by adding a car security wire schematic, car alarm wire diagram, car remote starter wire diagram, auto remote starter wire diagram or auto security wire diagram to our resource, please feel free to post any additional car wiring information about the 1998 Chrysler LHS on this page.

1998 Chrysler LHS Auto Alarm Wiring Diagram

Battery Constant 12v+ Positive Wire (+): Pink/Black and Red
Battery Constant 12v+ Positive Wire Location: Ignition Switch Harness

Starter Positive Wire (+): Yellow
Starter Positive Wire Location: Ignition Switch Harness

Ignition Positive Wire (+): Dark Blue/White
Ignition Positive Wire Location: Ignition Switch Harness

Second Ignition Positive Wire (+): Green/Red
Second Ignition Positive Wire Location: Ignition Switch Harness

Accessory Positive Wire (+): Black/Orange
Accessory Positive Wire Location: Ignition Switch Harness

Second Accessory Positive Wire (+): Black/White
Second Accessory Positive Wire Location: Ignition Switch Harness

Parking Light Negative Wire (-): Yellow (The parking lights require an extra relay and a (-) negative through a 110 ohm resistor to connect.)
Parking Light Negative Wire Location: At Headlight Switch

Parking Light Positive Wire (+): Do Not Use!
Parking Light Positive Wire Location: N/A

Power Door Lock Negative Wire (-): White/Green (1-Wire Door Lock System). The door locks on this vehicle require a (+) positive through a 2700 ohm resistor to lock and a (+) positive thru a 620 ohm resistor to unlock, some units will also require 2 extra relays for the keyless entry feature to work properly.
Power Door Lock Negative Wire Location: At Back Of Fuse Box

Power Door Unlock Negative Wire (-): Same Wire As Above.
Power Door Unlock Negative Wire Location: N/A

Door Trigger Wire: Tan (-) And Tan/Red (-) (Use Both). This vehicle uses 2 door trigger wires, when connecting to an alarm system, use both wires and diode isolate.
Door Trigger Wire Location: At BCM. The BCM (body control module) is located under the driver’s side dash attached to the junction block.

Dome Light Supervision Wire: Yellow (-), Requires Relay
Dome Light Supervision Wire Location: At Rear Of Fuse Box, Brown Plug

Trunk Release Positive Wire (+): Black/White (Requires Relay)
Trunk Release Positive Wire Location: At Trunk Release Switch

Horn Negative Wire (-): Black/Red (-)
Horn Negative Wire Location: At Steering Column Harness

Tachometer Wire Negative Wire (-): This vehicle is a multi-coil pack ignition system, the tachometer wire will be any wire with a tan stripe at the coil pack.
Tachometer Wire Negative Wire Location: At Ignition Coil Pack

Brake Light Positive Wire (+): White/Tan
Brake Light Positive Wire Location: At Switch Above Brake Pedal

Factory Alarm Disarm Wire (+): Light Green/Orange (The disarm wire requires an extra relay and a (+) positive through a 680 ohm resistor to connect.)
Factory Alarm Disarm Wire Location: In Drivers Kick Panel

Factory Anti-Theft System: Chryslers Sentry Key (Gray Key Only) A Transponder System
Factory Anti-Theft System Location: Transponder At Ignition Switch Tumbler

8 thoughts on “1998 Chrysler LHS Auto Alarm Wiring Diagram”

  1. Mike, as much as we would like to help you, not all car alarms are installed the same way. Different brands and different setups will call for different wiring. Our advice is to take your car to a qualified alarm installer and ask them how to disarm the alarm because it does take some wiring knowledge and experience to know what to do. Hope this helps. Good luck on your 1998 Chrysler Sebring alarm troubleshooting.

  2. Robert, as much as we would like to help you, not all car alarms are installed the same way. Different brands and different setups will call for different wiring. Our advice is to take your 1999 Chrysler Sebring to a qualified alarm installer and ask them to remove the alarm because it does take some wiring knowledge and experience to know what to remove. Hope this helps. Good luck on your 1999 Chrysler Sebring alarm removal.

  3. Brandi, it really depends on how the alarm was installed and which alarm was installed. Different car alarms and different setups will call for different wiring. Our advice is to take your car to a qualified alarm installer and ask them to remove the alarm because it does take some wiring knowledge and experience to know what to remove. Hope this helps. Good luck on your alarm removal.

  4. Jim, as much as we would like to help you, not all car alarms are installed the same way. Different brands and different setups will call for different wiring. Our advice is to take your car to a qualified alarm installer and ask them to remove the alarm because it does take some wiring knowledge and experience to know what to remove. Hope this helps. Good luck on your alarm removal.

  5. How do I disable the alarm system on the 1998 Chrysler Sebring Convertible. We no longer have an alarm set/unlock piece. Car will not start at all. Last week had same problem. reset button under front seat worked then but not doing anything now. Thought about just removing fuse but according to book, numerous other applications also controlled by same 20 amp fuse. Please help, thanks.

Leave a Comment

Your email address will not be published. Required fields are marked *